« 753 SAGE JEEP ”ORIGINAL PATCH” CAP
i have a 96 jeep grand cherokee, the charging system is not working? »

StrongArm 4699 Jeep Grand Cherokee Liftgate Lift Support 1999-03, Pack of 1

  • Exact fit, OE quality design ensures easy installation and precise operation
  • No special installation tools required
  • Rubber O-Ring piston seal forces the fluid efficiently through the valving components providing consistent performance
  • Patented Multi-Lobe Seal makes gas springs more tolerant to vibration and temperature extremes
  • Individually tested for performance and reliability

Product Description
StrongArm gas charged lift supports are custom engineered and manufactured beyond industry standards to provide smooth operation and durability. The hardened chromium plated steel shaft is precision ground and polished for superior corrosion resistance and leak free sealing. The self cleaning piston assembly automatically opens during each compression cycle to keep the orifice clear of fluid contaminants and provide smoother operation and reliable performance. Most units also utilize StrongArm’s patented temperature compensation module valve which ensures consistent operation even in extreme weather conditions. It does so by compensating for normal gas pressure changes caused by temperature variations. The metallic upper bushing is manufactured with bearing quality precision to provide exact fit with pistion rod and promote a long operating life…. More >>

StrongArm 4699 Jeep Grand Cherokee Liftgate Lift Support 1999-03, Pack of 1

Incoming search terms for the article:

5 Responses to “StrongArm 4699 Jeep Grand Cherokee Liftgate Lift Support 1999-03, Pack of 1”

  1. S. Mejeur Says:
    March 31st, 2010 at 6:54 am

    I gambled and only ordered one for my 2002 Jeep Grand Cherokee, figuring I could remove both originals and test each to see which was failing and only replace that one. Well, with both removed, they both had more than enough pressure for me to figure out how to test them. If I had to do it again, I’d remove one, test the pressure on the door with only one, then reinstall the first, remove the second and test the one that was removed first. So I didn’t think about that at the time & just decided to replace one at random. It did the trick, door works perfect. This replacement does appear to be a little longer than stock, which makes starting the second mounting bolt easy to cross-thread or not start at all. As other people have commented, you can work around this easily by simply having a second person to lift the door to full extension. Simply propping the door up with a ladder or board will not do. Good luck!
    Rating: 5 / 5

  2. J. Roy Says:
    March 31st, 2010 at 8:37 am

    I installed these struts on a 2000 JGC. The same strut works on both the left and right sides. You’ll have to twist the cylinder to line up the bolts. Make it easier on yourself and have someone hold the liftgate up while you’re replacing the struts.
    Rating: 5 / 5

  3. Glenn C. Prieto Says:
    March 31st, 2010 at 9:39 am

    The installation was very fast and easy. I bought this both for the rear hatch and the hood. They work great and I ended up saving over $100 bucks if I would of taken it to the dealership. It was well worth it!
    Rating: 5 / 5

  4. N. Polcar Says:
    March 31st, 2010 at 10:41 am

    Great value allround. I replaced the Lift support for the hood on my jeep and hood stays up when im working on the engine. Im so happy easy to install and was delivered quick.
    Rating: 5 / 5

  5. Ed mtb Says:
    March 31st, 2010 at 1:23 pm

    I got this for my 1999 Jeep Grand Cherokee Laredo, and it fit perfect. Besides an ornary bolt, it was easy to install and took about 5 minutes. You do need a special star shaped bit to unscrew the bolt. My liftgate only wouldn’t hold up in cold weather, so I only replaced one strut, and that was plenty.
    Rating: 5 / 5

Leave a Reply